|
 |
Extruded Rubber "U" Channel
Military Grade |
 |
|
Extruded Rubber "U" Channel - Channel dimensions shall be in accordance with the table below. All corner and fillet radii shall be 0.015. Toterance for channel length shall be -0%, +3%.
 |
Extruded Rubber Channel
| Dimensional Range |
Tolerance |
| 0.015 to 0.040 inclusive |
+/- 0.005 |
| Greater than 0.041 to 0.062 inclusive |
+/- 0.012 |
| Greater than 0.062 to 0.125 inclusive |
+/- 0.016 |
| Greater than 0.125 to 0.187 inclusive |
+/- 0.020 |
| Greater than 0.187 to 0.375 inclusive |
+/- 0.031 |
| Greater than 0.375 to 0.562 inclusive |
+/- 0.047 |
| Greater than 0.562 to 0.750 inclusive |
+/- 0.063 |
| Greater than 0.750 to 1.000 inclusive |
+/- 0.093 |
| 0.100 and greater |
+/- 10% dim. |
| |
|
|
| Please Note: Each of the seven (7) noted dimensions in the diagram below; i.e. A, B, C, D, E, F and G, are required to determine the tooling requirement for manufacturing a particular type of Extruded Rubber "U" Channel material.
|
| 
|
| Standard Extruded Rubber "U" Channel Configurations are listed bellow. The channel measurements listed below refer to the elements of the channel labeled in the above drawing. This material is supplied in continuous rolls of from between 300 to 500 linear feet depending on what is being ordered. There are certain minimum quatities depending on the item being ordered. Such minimum quantities will be noted when items are being quoted.
Please note: We are unable to "splice" this material. |
| Configuration Handle |
A |
B |
C |
D |
E |
F |
G |
| 3584-034-1103 |
0.250" |
0.188" |
0.125" |
0.125" |
0.062" |
0.062" |
0.062" |
| 3584-064-1108 |
0.250" |
0.250" |
0.125" |
0.125" |
0.125" |
0.125" |
0.250" |
| 3584-094-1103 |
0.250" |
0.500" |
0.125" |
0.125" |
0.062" |
0.062" |
0.062" |
| 3584-124-1410 |
0.250" |
0.875" |
0.125" |
0.125" |
0.125" |
0.125" |
0.625" |
| 3582-021-3101 |
0.312" |
0.156" |
0.062" |
0.250" |
0.062" |
0.062" |
0.031" |
| 3582-051-3105 |
0.312" |
0.240" |
0.062" |
0.250" |
0.062" |
0.062" |
0.114" |
| 3582-061-3107 |
0.312" |
0.300" |
0.062" |
0.250" |
0.062" |
0.062" |
0.174" |
| 3582-096-1408 |
0.312" |
0.500" |
0.187" |
0.125" |
0.125" |
0.125" |
0.250" |
| 3582-124-2410 |
0.312" |
0.875" |
0.125" |
0.187" |
0.125" |
0.125" |
0.625" |
| 3582-134-2411 |
0.312" |
1.000" |
0.125" |
0.187" |
0.125" |
0.125" |
0.750" |
| 3583-084-3410 |
0.375" |
0.875" |
0.125" |
0.250" |
0.125" |
0.125" |
0.625" |
| 3582-094-3411 |
0.312" |
1.000" |
0.125" |
0.250" |
0.125" |
0.125" |
0.750" |
| 3584-072-5208 |
0.438" |
0.375" |
0.063" |
0.375" |
0.063" |
0.063" |
0.250" |
| 3584-054-4408 |
0.438" |
0.500" |
0.125" |
0.313" |
0.125" |
0.125" |
0.250" |
| 3585-022-6201 |
0.500" |
0.156" |
0.063" |
0.437" |
0.063" |
0.063" |
0.031" |
| 3585-094-5408 |
0.500" |
0.500" |
0.125" |
0.375" |
0.125" |
0.125" |
0.250" |
| 3585-014-5411 |
0.500" |
0.100" |
0.125" |
0.375" |
0.125" |
0.125" |
0.750" |
| 3585-017-3509 |
0.500" |
0.100" |
0.250" |
0.250" |
0.250" |
0.250" |
0.500" |
| 3588-124-0410 |
0.875" |
0.875" |
0.125" |
0.750" |
0.125" |
0.125" |
0.625" |
| 3589-127-0508 |
1.000" |
1.000" |
0.250" |
0.750" |
0.250" |
0.250" |
0.500" |
| 3581-134-1404 |
0.250" |
1.250" |
0.125" |
0125" |
0.125" |
0.125" |
0.100" |
| 3582-114-2409 |
0.312" |
0.750" |
0.125" |
0.187" |
0.125" |
0.125" |
0.500" |
| 3582-116-1409 |
0.312" |
0.750" |
0.187" |
0125" |
0.125" |
0.125" |
0.500" |
| 3583-084-3406 |
0.375" |
0.375" |
0.125" |
0.250" |
0.125" |
0125" |
0.125" |
| 3583-134-3412 |
0.375" |
1.250" |
0.125" |
0.250" |
0.125" |
0.125" |
1.000" |
| 3583-137-1403 |
0.375" |
1.250" |
0.250" |
0.125" |
0.125" |
0.125" |
0.100" |
| 3583-147-1413 |
0.375" |
1.500" |
0.250" |
0.125" |
0.125" |
0.125" |
1.250" |
| 3583-147-1512 |
0.375" |
1.500" |
0.250" |
0.125" |
0.250" |
0.250" |
1.000" |
| 3583-177-1513 |
0.375" |
1.750" |
0.250" |
0.125" |
0.250" |
0.250" |
1.250" |
| 358X-XXX-XXXX |
|
|
|
|
|
|
|
| 3583-187-15145 |
0.375" |
2.500" |
0.250" |
0.125" |
0.250" |
0.250" |
2.000" |
| 358X-XXX-XXXX |
|
|
|
|
|
|
|
| 3583-214-3417 |
0.375" |
3.250" |
0.125" |
0.250" |
0.125" |
0.125" |
3.000" |
| 358X-XXX-XXXX |
|
|
|
|
|
|
|
| 3583-227-1517 |
0.375" |
3.500" |
0.250" |
0.125" |
0.250" |
0.250" |
3.000" |
| 3583-237-1518 |
0.375" |
4.000" |
0.250" |
0.125" |
0.250" |
0.250" |
3.500" |
| 3583-247-1519 |
0.375" |
4.500" |
0.250" |
0.125" |
0.250" |
0.250" |
4.000" |
| 3589-104-541X |
0.500" |
0.625" |
0.125" |
0.375" |
0.125" |
0.125" |
--- |
| 3583-167-3414 |
0.500" |
1.750" |
0.250" |
0.250" |
0.125" |
0.125" |
1.500" |
| 3583-177-3415 |
0.500" |
2.250" |
0.250" |
0.250" |
0.125" |
0.125" |
2.000" |
| 3583-207-3516 |
0.500" |
3.000" |
0.250" |
0.250" |
0.250" |
0.250" |
2.500" |
| 3586-114-7409 |
0.625" |
0.750" |
0.125" |
0.500" |
0.125" |
0.125" |
0.500" |
| 3586-258-3620 |
0.625" |
5.750" |
0.375" |
0.250" |
0.375" |
0.375" |
5.000" |
| 3586-268-3621 |
0.625" |
6.750" |
0.375" |
0.250" |
0.375" |
0.375" |
6.000" |
| 3586-045-7302 |
0.625" |
0.203" |
0.156" |
0.500" |
0.078" |
0.078" |
0.047" |
| 3586-043-8302 |
0.625" |
0.203" |
0.078" |
0.578" |
0.078" |
0.078" |
0.047" |
| 3587-084-94XX |
0.750" |
0.375" |
0.125" |
0.625" |
0.125" |
0.125" |
--- |
| 3587-094-94XX |
0.750" |
0.500" |
0.125" |
0.625" |
0.125" |
0.125" |
--- |
| 3583-167-14XX |
0.375" |
1.750" |
0.250" |
0.125" |
0.125" |
0.125" |
--- |
| 3587-174-94XX |
0.375" |
2.250" |
0.250" |
0125" |
0.125" |
0.125" |
--- |
| 3587-194-94XX |
0.375" |
2.750" |
0.250" |
0.125" |
0.125" |
0.125" |
--- |
| 3587-214-94XX |
0.375" |
3.250" |
0.250" |
0125" |
0.125" |
0.125" |
--- |
| 3580-045-73XX |
0.656" |
0.203" |
0.156" |
0.500" |
0.078" |
0.078" |
--- |
| 3581-244-1519 |
0.250" |
4.500" |
0.125" |
0.125" |
0.250" |
0.250" |
4.000" |
| 3581-224-1517 |
0.250" |
3.500" |
0.125" |
0.125" |
0.250" |
0.250" |
3.000" |
| |
|
|
|
|
|
|
|
|
| How to Request a Custom Quotation
-
1. Please determine the appropriate Standard Extruded Rubber "U" Channel required for the current applcation and the number of lianer feet needed to accomplish the task.
2. If custom dimensions are required, please provide a sketch indicating the appropriate dimensions along with the total number of linear feet needed.
3. Please include contact name, company name, telephone number, fax number, e-mail address and destination city, state and Zip Code for the shipping part of the proposal.
Thank you. |
|
|
| |
| |
| THE
MAT KING
740 West End Avenue; Suite 1
New York, NY 10025 USA
Phone: 646-998-4208
Fax: 646-998-4073
Phone: 800-442-6544
Fax: 800-Mats-Fax (628-7329)
 |
| |
|
|
