Directions:
1. Please read all directions before using. Use in a well-ventilated area only. Surface should be clean, dry and free from dirt. Roughen surface before use. Best when used between 70°F (21°C) and 85°F (29°C). Test small area before full use.
2. Apply E-6000 directly to the area to be repaired. For maximum strength, allow bond to dry for 24 to 72 hours. Cure time increases with lower temperatures and decreases with higher temperatures. Speed drying time by using a hand-held hair dryer. Set on low and do not hold directly on E-6000.
3. Clean uncured adhesive with acetone or naphtha. Cured material may be removed by cutting and scraping.
4. If E-6000 is used to adhere articles to fabric, DO NOT DRY CLEAN FABRIC.
5. E-6000 is not recommended for use on Styrofoam™, polystyrene, polyethylene or polypropylene plastics.
To request a Material Safety Data Sheet (MSDS) please send an email to msds@eclecticproducts.com
Specifications:| E-6000 | |
| UNCURED MATERIAL | CURED MATERIAL |
| Solids:
30% by weight Density: 11.1 lbs./gal. VOC: 1.198 grams/liter Tack time: 5 minutes Full cure time: thin film: 24 hours; thick film: 48-72 hours Storage: store between 50°F (10°C) and 80°F (27°C) Freeze/thaw stability: yes; allow product to reach room temperature before opening Color: clear, white, gray, black Viscosity: 50,000 cps (low), 100,000 cps (medium), 200,000 cps (high) Shelf life: 1 year, unopened |
Hardness:
80A Tensile strength: 3,500 lb/in2 (ASTM D-412) Elongation: 900% (ASTM D-412) Chemical resistance: excellent to water, dilute acids & bases Temperature range: -40°F (-40°C) to 150°F (66°C) Paint-over time: 24 hours UV resistance: paint over or use UV-6800™ Dielectric strength: 400 V/mil (ASTM D-149) |
| E-6100 | |
| UNCURED MATERIAL | CURED MATERIAL |
| Solids:
32% by weight Density: 11.0 lbs./gal. VOC: 1.198 grams/liter Tack time: 4 minutes Full cure time: thin film: 24 hours; thick film: 48-72 hours Storage: store between 50°F (10°C) and 80°F (27°C) Freeze/thaw stability: yes; allow product to reach room temperature before opening Color: clear, white, gray, black Viscosity: non-sag Shelf life: 1 year, unopened |
Hardness:
80A Tensile strength: 3,800 lb/in2 (ASTM D-412) Elongation: 900% (ASTM D-412) Chemical resistance: excellent to water, dilute acids & bases Temperature range: -40°F (-40°C) to 150°F (66°C) Paint-over time: 24 hours UV resistance: paint over or use UV-6800™ Dielectric strength: 400 V/mil (ASTM D-149) |
| UV-6800 | |
| UNCURED MATERIAL | CURED MATERIAL |
| Solids:
30% by weight Density: 11.1 lbs./gal. VOC: 1.198 grams/liter Tack time: 5 minutes Full cure time: thin film: 24 hours; thick film: 48-72 hours Storage: store between 50°F (10°C) and 80°F (27°C) Freeze/thaw stability: yes; allow product to reach room temperature before opening Color: clear. Viscosity: 100,000 cps Shelf life: 1 year, unopened |
Hardness:
80A Tensile strength: 3,500 lb/in2 (ASTM D-412) Elongation: 900% (ASTM D-412) Chemical resistance: excellent to water, dilute acids & bases Temperature range: -40°F (-40°C) to 150°F (66°C) Paint-over time: 24 hours UV resistance: to maximize UV resistance, paint over or use UV-6800™ Dielectric strength: 400 V/mil (ASTM D-149) |
Back to E-600 Family of Adhesives Introduction
Site Map: The Mat King Web Site in Overview
 |
 |
 |
THE
MAT KING
740 West End Avenue; Suite 1
New York, NY 10025 USA
Phone: (646)998-4208
Fax: (646)998-4073
Phone: 800-442-6544
Fax: 800-Mats-Fax (628-7329)
Phone: 800-442-6544
Fax: 800-Mats-Fax (628-7329)
|
||||
|
