ULTRASEAL ADHESIVE PART "A"
MATERIAL SAFETY DATA SHEET
MSDS
THIS ITEM HAS BEEN DISCONTINUED
THANK YOU
SECTION I - PRODUCT IDENTIFICATION
CHEMICAL FAMILY : Aromatic Isocyanate Mixture
TRADE NAME AND SYNONYMS : Ultraseal Component A
FORMULA : The specific chemical formula for this material is a
Trade Secret of the manufacturer.
SECTION II - HAZARDOUS INGREDIENTS
INGREDIENT: TLVL
Modified Diphenylmethane
Diisocyanate .1 ppm Skin (ACGIH)
SECTION III - PHYSICAL DATA
APPEARANCE: Beige Liquid .
ODOR: Slight
COLOR: Beige
BOILING POINT (F) (C): 300 C
SPECIFIC GRAVITY: .92- .94
PERCENT VOLATILE (by volume): 0
EVAPORATION RATE (ether = 1): Slower
VAPOR DENSITY (air = 1): Greater
SOLUBILITY IN WATER (percent): None
IMPORTANT:
The data in this Material Safety Data Sheets relates to the material designated
herein and does not relate to use in combination with any other material or
in any process. The information herein is furnished free of charge and is based
on the technical data that the manufacturer believes to be reliable, and to
the best of our knowledge, accurately reflects the properties and effects of
the hazardous components. This product is intended for use by persons having
technical skills and at their own discretion and risk. Because conditions of
use of this material are outside our control, we make no warranties, expressed
or implied, and assume no liability in connection with any use of this material.
SECTION IV -FIRE AND EXPLOSION HAZARD DATA
FLASH POINT: 100 C. (T.C.C., ASTM D-45-70)
EXTINGUISHING MEDIA : Water Spray (fog), foam, dry chemical,
carbon dioxide
SPECIAL FIRE FIGHTING PROCEDURES: Full protective equipment with self-contained
breathing apparatus should be worn.
UNUSUAL FIRE & EXPLOSION HAZARDS: Keep containers tightly closed. Isolate
from heat, electrical equipment, sparks and open flame. Water spray may be used
to cool closed containers and prevent pressure build up. Empty containers may
contain liquid or vapor which is flammable or explosive. DO NOT weld, burn or
cut empty containers.
SECTION V -HEALTH HAZARD DATA
EFFECTS OF OVEREXPOSURE
EYES: Eye irritant. Wash with water for at least 15 minutes. Consult a
physician.
SKIN: Skin irritant and possible skin sensitizer. Wash with tincture of green
soap and water. Consult a physician if irritation persists.
INHALATION: Inhalation of vapors or spray mist may also cause irritation to
the respiratory tract. Remove to uncontaminated area. Administer oxygen if available
and necessary; however, due to low vapor pressure overexposure is not expected
under normal conditions unless material is heated or used in poorly ventilated
area. .
INGESTION: Drink water to reduce corrosiveness. Consult a physician. Over exposure
may lead to mucous membrane irritations, tightness of chest, respiratory tract
irritation, coughing, headache and shortness of breath. May lead to allergic
sensitivity in some individuals resulting in asthma-like symptoms upon subsequent
exposure below TL V.
SECTION VI -REACTIVITY DATA
STABILITY : Stable under normal conditions.
CONDITIONS TO A VOID: Contact with mtisture and alkaline materials; temperatures
above maximum storage temperature.
INCOMPATIBILITY (materials to avoid): Contact with water and strong bases.
HAZARDOUS DECOMPOSITION PRODUCTS: By high heat and fire, carbon monoxide, oxideh
of nitrogen, aniline and solvent vapors.
HAZARDOUS POLYMERIZATION: Will not occur under normal conditions.
anbsp;
SECTION VII -SPILL OR LEAK PROCEDURES
TAKE THE FOLLOWING STEPS IF MATERIAL IS RELEASED OR SPILLED:
Workers should avoid direct skin or eye contact or inhalation of any vapors.
Absorb on dry inert material. Package for disposal.
WASTE DISPOSAL METHOD: Dispose of in accordance with local, state and federal
regulations.
SECTION VIII -SPECIAL PROTECTION INFORMATION
RESPIRATOR Y PROTECTION: If working in conditions where TL V is exceeded, use
a chemical cartridge mask or air supply hood as required and/or approved by
ANSI and OSHA.
VENTILAT ON REQUIREMENTS: N/A
EYE PROTECTION: Splash goggles or frce shield required. A full face
shield is recommended for most situations as it affords eye as well as face
protectikn.
OTHER PROTECTIVE EQUIPMENT: Chemical resistant gloves apron or coveralls, and
face shield are required. If protective creams are used, minimize the are protected
only by the cream.
SECTION IX -SPECIAL PRECAUTIONS
STORAGE TEMPERATURE: 100 F (38 C) maximum
SHELF LIFE: Minimum one (1) year at 75 F (23 C)
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING : Keep containers closed when
not in use. Keep away from heat, sparks and open flame. Store in tightly sealed
containers and keep away from moisture and direct sunlight.
OTHER: Wear personal protective equipment when working on equipment that may
be contaminated with material.
EMPTY CONTAINERS : All label precautions must be observed when handling or transporting
empty containers due to product residues. Residues may be neutralized by rinsing
container with respective Ultraseal, Component B and allowing components to
react and cure. Empty containers must be disposed of in accordance with local,
state and federal regulations.
SECTION X -SHIPPING DATA
D.O.T. SHIPPINGNAME : Coating Solution
TECHNICAL SHIPPING NAME : Polyurethane Resin
D.O. T. HAZARD CLASSIFICATION..: Non-Flammable
D.O. T. LABELS REQUIRED : None
D.O. T. PLACARDS REQUIRED : -None
FREIGHT CLASS : 1
LIMIT, AIR FREIGHT : None
To Ultraseal Adhesive Part "B" MSDS
Back to Ultraseal Adhesive Product Page
Site Map: The Mat King Web Site in Overview
|
